This is the glow or electric powered, radio controlled, 1/8 scale Ofna X3 Sabre Pro Off-Road Buggy Kit. **This version contains the Electric Conversion Kit.** FEATURES: Chassis: 0.12" (3mm) thick 7075 aluminum lightened chassis with countersunk screw holes and 7075 CNC aluminum front and rear braces, composite stone guards and rear mud deflectors Electric Conversion Kit: Three hook and loop battery straps, 5.9 x 2 x 0.67" (150 x 52 x 17mm) battery box holds a variety of 2S-4S LiPo batteries, electric chassis, and motor mount Drive: Four wheel shaft, lightweight CVA drivetrain Ball Bearings: Full set Shocks: Version 2 aluminum body, oil-filled, two sets of springs Shock Towers: 0.20" (5mm) thick CNC aluminum Differentials: Oil-filled, bevel gear Engine Mounts: 7075 etched aluminum Exhaust: Chrome finish, EFRA approved 2080 one-piece tuned pipe and header Clutch: Three-shoe aluminum with 14 tooth steel clutch bell Fuel Tank: 4.2oz (125cc) Body: Clear polycarbonate, cab forward design, with high-impact downforce wing in white Brake: Side loaded caliper with 1.1" (27mm) fiberglass disc Steering: Ball bearing equipped with servo saver and adjustable Ackerman, Ackerman describes the effect of the inner front wheel rotating faster than the outer wheel during turns, 22° steering hubs Suspension: Full travel, front and rear sway bars, steel captured hinge pins Tires: Square and rectangular spikes, 4.2" (107mm) diameter, 1.69" (43mm) wide, foam inserts Wheels: White dish style, diameter: 3.31" (84mm), width 1.69" (43mm) hex size: .47" (17mm) Caster: Adjustable, caster/toe-in refers to the angle of the front suspension when viewed from the side of the car in relation to the chassis Camber: Adjustable front and rear, camber refers to the angle of the tops of the tires from vertical when viewed from front or behind vehicle INCLUDES: X3 Sabre Pro Off-Road Buggy Kit with Tires, Foam Inserts, Wheels, Tuned Pipe, Header, Shocks with extra set of Springs, Clear Body, Wing, Fuel Tank, Air Filter, Decals, Instruction Manual, Chassis for electric Motors, Motor Mount, Battery Box, Hook and Loop Battery Straps REQUIRES: Radio: Two-channel with high torque servo Engine: .21 cu in (3.4cc) rear exhaust, non pull-start Receiver Battery: 5-cell 6V flat pack AA Batteries: Four or eight depending on transmitter Starter box, glow starter, glow fuel & building and track equipment SPECS: Vehicle- Length: 20.28" (515mm) Front Width: 12.1" (307mm) Rear Width: 11.9" (303mm) Height: 7.4" (188mm) Wheelbase: 12.6" (325mm) Weight: 7.27lbs (2721g) Body- Length: 14.5" (369mm) Width: 7.5" (190mm) Height: 3.8" (97mm) COMMENTS: For Replacement Ball Bearings use: Qty. Size Location Qty. Bearing Set 4 8x16mm Fr & Rear Diff 2 DTXC1585 1 8x16mm Spur Gear 1 DTXC1585 2 5x8mm Fr Gear Case 1 DTXC1523 2 8x14mm Fr Knuckle Arms 1 DTXC1583 2 13x20mm Fr Knuckle Arms not carried 2 8x14mm Rear Knuckle Arms 1 DTXC1583 2 13x20mm Rear Knuckle Arms not carried 4 6x10mm Steering 2 DTXC1561 2 5x11mm Rear Gear Case 1 DTXC1547 2 5x10mm Clutch 1 DTXC1535 jxs 02/08/12 ir/jxs