This is the radio controlled, glow or gasoline powered, almost ready to fly Giant P-40 Warhawk from Top Flite. FEATURES: Construction: Balsa & ply and fiberglass Wing: One-piece Aileron Control: Dual servo with dual servo flap control Cowl: Painted fiberglass Canopy: Clear with painted-on frame lines, detailed cockpit with instrumentation Spinner: Aluminum 5.5" (140mm) diameter, painted red Covering: Matte finish MonoKote Landing Gear: Heavy duty fixed, 5" (127mm) diameter main foam wheels, 1-1/2" (38mm) foam tailwheel **Robart makes a set of giant scale 100° rotating retracts for this model ROBQ1665, see COMMENTS Fuel Tank: 24oz (720cc), approximate Building Time: Ready to fly in several hours Warranty: Top Flite Models guarantees this kit to be free of defects in material and workmanship at the date of purchase. This warranty does not cover any component parts damaged by use or modification. INCLUDES: Pre-built fuselage wing and tail assemblies, decals, landing gear, wheels, spinner, hardware package, fuel tank, cockpit detail and photo-illustrated instruction manual REQUIRES: Engine: 2.6 - 3.3 cu in (43 - 55cc) gasoline or glow, (the DLE 55 DLEG0055 is recommended. The manual provides specific instructions for the mounting of this engine. Modifcations may be needed if mounting other engines. See COMMENTS Muffler: To match selected engine, J"TEC makes a muffler (JTCG1040) specifically for use with this airplane and the DLE 55 engine Radio: At least 5-channel, 6-channel needed if installing retractable landing gear Servos: Nine, all control surfaces require high-torque servos, servos with 40 oz-in of torque can be used for throttle, choke and air valve Heavy Duty 24" (310mm) Servo Extensions: Two for ailerons Heavy Duty 12" (305mm) Servo Extensions: Five, two for flaps, two for elevator, one for rudder Y-Harnesses: One each for aileron, flaps & elevator Receiver Battery: At least 1500mAh Heavy Duty Switch Harness: Two Charge Receptacle: Two Servo Arms: Two 1", one 2" Building and Field Equipment SPECS: Wingspan: 86" (2,185mm) Wing Area: 1,262in² (81.4dm²) Weight: 23-24lb (10.43-10.88kg) Wing Loading: 42-44oz/ft² (128-134g/dm²) Length: 72" (1,830mm) Airfoil: Semi-symmetrical Center of Gravity (CG): 5.5" (140mm) back from the leading edge of the top of the wing on both sides of the fuselage Control Throws- Low Rate High Rate Elevator Up & Down: 3/4" (19mm) 10° 1" (25mm) 13° Rudder Right to Left: 1" (25mm) 9° 1-7/8" (48mm) 18° Ailerons Up & Down: 3/4" (19mm) 13° 1" (25mm) 18° Flaps: 2-1/2" (64mm) 36° COMMENTS: If modeler is using the DL-55cc engine, the stock muffler will not fit in the cowling and the J"TEC Pitts Wraparound Muffler (JTCG1035) must be used for a clean installation. If modeler is installing the giant scale 100° rotating retracts, the following items are required; #157VR Large Air Control Kit, ROBQ2305 #169 Pressure Tubing 10" ROBQ2369 #160LWC LH Offset Pneumatic Tail Wheel, ROBQ2225 Following are the colors of Top Flite MonoKote used to cover this model and the order numbers for 6" rolls; Flat Olive Drab, TOPQ0510 Flat Dove Gray, TOPQ0511 Flat Tan, TOPQ0516 Missile Red, TOPQ0201 Flat Black, TOPQ0508 jxs 05/10/10