This is the 1/10 scale, electric powered, 2.4GHz radio controlled, RTR HPI On-Road Sprint 2 Drift Car with the 2010 Chevrolet Camaro Body. FEATURES: Chassis: 3/16" (4mm) thick plastic Drive: Four wheel belt drive Motor: Firebolt 15 turn brushed Radio: HPI TF-40 2.4GHz with waterproof steering servo and waterproof receiver box Electronic Speed Control: HPI SC-15WP LiPo compatible, waterproof and reversible Battery: 7.2V 2000mAh Battery Charger: AC wall type Ball Bearings: Full set included Shocks: Oil-filled, aluminum bodied with special drifting springs Differentials: Planetary gear with metal outdrives Transmission: Single speed Tires: Falken Azenis hard plastic drift tires, width 1.02" (26mm), 2.5" (63mm) diameter Wheels: Officially licensed 5-spoke Rays Volk wheels with 6mm offset, outer diameter: 1.9" (48mm), width: 1.0" (26mm) Pinion Gear: 28 tooth 48 pitch metal Spur Gear: 48 pitch, 87 tooth, composite construction Body: Painted and trimmed 2010 Camaro Bumper: Front, foam Suspension: Fully adjustable Ackerman: Adjustable, Ackerman describes the effect of the inner front wheel turning faster than the outer front wheel during turns Caster: Adjustable, caster/toe-in refers to the angle of the front suspension when viewed from the side of the car in relation to the chassis Camber: Adjustable front and rear, camber refers to the angle of the tops of the tires from vertical when viewed from front or behind vehicle Steering: Ball race bell-crank type with servo saver Warranty: Two year limited warranty through HPI beginning at purchase date. Valid only in the USA, Canada and South America INCLUDES: HPI On-Road Drift 2010 Camaro with motor, electronic speed control, painted body, drift tires, wheels, 28 tooth pinion gear AA batteries for radio, 2000mAH battery, wall charger, 87 tooth spur gear, 2.4GHz radio, steering servo, decal sheet, 15T motor and instructions _ IEQUIRES: Misc. Items: Building and track equipment SPECS: VEHICLE- Length: 17" (431mm) Width: 7.5" (190mm) - 8.0" (190mm) adjustable using offset wheels Height: 5" (127mm) Wheelbase: 10" (255mm) Front Track: 7.38" (187.5mm) side to side at outer edges of wheel Battery Charger: To match selected battery Paint: Polycarbonate safe spray or brush-on Misc. Items: Building and track equipment Front Tread: 6.5" (166mm) Rear Tread: 7.2" (183mm) side-to-side at wheel centers Ground Clearance: 0.5" (13mm) BODY- Length: 17.1" (434mm) Width: 7.75" (197mm) at rear wheels (widest point) 6.6" (169mm) behind from wheels (thinnest point) Height: 4.4" (111mm) COMMENTS: For Replacement Ball Bearings use: Qty. Size Location Qty. Bearing Set 4 5x10mm Fr Wheels 2 DTXC1535 4 5x10mm Rear Wheels 2 DTXC1535 2 10x15mm Fr Diff 1 DTXC1595 2 2x8mm Fr Diff 1 DTXC1523 2 10x15mm Rear Diff 1 DTXC1595 2 2x8mm Rear Diff 1 DTXC1523 2 4x8mm Servo Saver 1 DTXC1511 2 4x8mm Middle Lay Shaft 1 DTXC1511 jxs 06/27/11 ir/jxs