This is the Futaba 6JA 6-Channel 2.4GHz S-FHSS and FHSS Selectable Mode Radio System with the R2006GS Receiver and four S3004 Servos. This is the airplane version with the ratcheted throttle stick. FEATURES: Selectable S-FHSS and FHSS modes, the included R2006GS receiver automatically adapts to the selected mode Capable of 4 channels only in FHSS mode Fail safe on all channels in S-FHSS mode only (throttle channel only when FHSS mode is selected) 15 model memory with 4 character model naming 40x40 127 segment LCD display Modes 1-4 selectable by pilot R2006GS high-voltage (4.8 - 7.4V) 6-channel receiver with Easy-Link circuitry, frequency hopping, spread spectrum design and Dual Antenna Diversity Endpoint adjustment (EPA), sub trims, servo reversing & throttle cut Throttle position, mix and low battery warnings Trainer system (trainer cord not included) One year limited warranty through Hobby Services beginning at date of purchase Airplane Features; Two programmable mixes and two 5-point throttle curves Two 5-point pitch curves Flaperon with differential rate Flap trim (2 rates) V-tail mixing Elevon mixing Helicopter Features; Two 5-point throttle curves Three 5-point pitch curves Throttle hold Hover pitch Gyro and revo mixing Four swash plate types (H1, H3, HR3 & H3 w/AFR) Swash AFR (ail/ele/pitch) Throttle mix Electronic swash ring Throttle and pitch delay INCLUDES: Futaba 6J 6-Channel Transmitter, R2006GS Receiver and Instruction Manual, Neckstrap, Servo Tray and Mounting Hardware, On/Off Switch and ratchet spring Four S3004 Standard Ball Bearing Servos, FUTM0004 **** There is an optional NiMH battery which can be used, FUTM1473. To use this, you will need to purchase a new battery door and charge lead from Futaba Services, see comments. REQUIRES: AA Cells: Four for transmitter SPECS: Transmitter; Type: 2-stick, 6-channel, FHSS/S-FHSS selectable Frame Rate: 6.8ms Current Drain: 170mA Receiver; Modes: FHSS or S-FHSS (auto selectable) Power Requirements: 4.8V-7.4V Compatible Batteries: NiCd, NiMH, LiPo, LiIon & LiFe Dimensions: 1-11/16 x 15/16 x 5/16" (43 x 24 x 7.9mm) Weight: 0.29oz (8.3g) Current Drain: 80mA (@ no signal) S3004 Servo; Speed: 0.23 sec/60° @ 4.8V 0.19 sec/60° @ 6.0V Torque: 44 oz-in (3.2 kg-cm) at 4.8V 57 oz-in (4.1 kg-cm) at 6.0V Dimensions: 1.6 x 0.8 x 1.4" (1-9/16 x 13/16 x 1-7/16") (40 x 20 x 36mm) Weight: 1.3 ounce (1-5/16oz) (37 grams) Connector: "J" type with approx. 5" wire COMMENTS: To use the NiMH battery FUTM1473, you will need to purchase charger FUTM1832. Than call Futaba Services at 217-398-8970 option 2 and they will send you a battery door- HSP82469. If you already have a charger and need a charge lead they can sell you part number- HSP29615. (requires soldering on the correct charger plugs) jxs 02/28/11 ir/jxs updt jxs 12/05/11 updt jpg 2/25/13